MAX can be positioned flush against a wall, into or around a corner. MAX works below the horizontal thus eliminating the need for scaffolding. MAX can be positioned parallel up to a 10' (305cm) ceiling. 16' (487cm) extension without adapter. 17.5' (533cm) extension with adapter. Self-leveling head with Baby Pin and Junior Receiver. Fast and easy setup or tear down. Easily movable at full extension on level surfaces. Angles are adjustable with light fixture attached. Use for lights, flags, frames, branch holders or even cameras. 3:1 weight ratio Features and Benefits Self Leveling head w/ baby pin and junior reciever Staight tracking, multi-direction locking, non-marking Tente casters. Best braking casters available. Weight Without Counterweights- 215 lb. With Counterweights- 465 lb.
The Dana Dolly Track Kit is a portable track kit for operators that wish to travel with their own dolly track. The triangular track is designed for use with the Dana Dolly, but should be compatible with most similar style dollies that use skateboard wheels set at 45°, and supports up to 100 pounds of camera, accessories and dolly. The kit includes six 3' track sections, nine track splicers, four end adapters, and necessary hardware to assemble 9' of track. Please note the kit only includes the triangular track and hardware, it does not include a Dana Dolly, Track Ends, or Center Support which must be purchased separately. The kit comes with enough track sections to assemble 9' of seamless dolly track. However, you can rent additional kits to extend your track beyond 9' Fully assembling the track requires eight track splicers, an extra splicer is included as a spare. The End Adapters allow you to attach the track to available Dana Dolly Original and Universal Track Ends, which are not included and must be sourced separately. Assembling the track only requires the use of the included "T" tool.
Trolley wheels on the C-Drive Kit make it easy to transport. The flightcase may also fit additional speedbags, C-Wheels, or Spigots. The Lightbridge CRLS C-Drive Kit contains the following: 1ea Flightcase 1ea 7x7 cm Cine Reflector Diff 1 - 4 + Sleeves 1ea 15x15 cm Cine Reflector Diff 1 - 4 + Sleeves 1ea 25x25 cm Cine Reflector Diff 1 - 4 + Sleeves 1ea 50x50 cm Cine Reflector Diff 1 - 4 + Sleeves 1ea 7x7 Cordura Bag 1ea 15x15 Cordura Bag 1ea 25x25 Cordura Bag 1ea 50x50 Cordura Bag 1ea Pouch 2ea C-Wheel female 2ea C-Wheel male 4ea Safety 1ea Cleaning Kit 2ea Safety Wedge Kit
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Extra leg sets are also available. Casters are available. We also carry staircases. Large staircase fits 3' and 4' leg usage, Small staircase fits 1' and 2' leg usage. DESCRIPTION: Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 2000 lbs. Load Capacity
The C-100 Kit frame has round edges that are safe for use in tight locations, including rigged on truss and in all weather conditions. Four holes on the corners of the frames are available for rope-ties. The clamp levers of the frames have a special designed C-Friction, which secures the lever and prevents it from coming unscrewed. Further, the corners are easily replaceable when undergoing wear and tear. The Lightbridge CRLS C-100 Kit contains the following: 1EA 100x100cm (39.4"x39.4") Double-Sided Frame with Diffusion 1-2 and Yoke 1EA 100x100cm (39.4"x39.4") Double Sided Frame with Diffusion 3-4 and Yoke 2EA 100x100cm Speed pads 1EA C-Cleaning Kit 1EA Manual
Multi-purpose, reliable, and strong, the Spring Clamp is an indispensable piece of equipment for photographers in need of an extra hand. Perfect for studio use, it’s built with impressive features for a superior grip. Compatible with bars of up to 40mm, you'll wonder how you ever worked without this handy add-on. This clamp, also compatible with light stands and hot shoes thanks to its adapter spigot, can be used for a variety of purposes. Use it to hold backdrops, hang lights, and even hold on to other clamps. Always ready to lend a helping hand, you'll be able to work faster and with greater efficiency. Featuring rubber feet, this clamp won't damage whatever it is attached to and ensures an extremely secure hold. Rest assured that you gear is protected with this top-quality choice. Easy to mount, it features a universal 15.9mm stud with a 9.35mm thread attachment, allowing you to use it with a variety of equipment. Customise your set up to your unique shooting needs and minimise any troubleshooting along the way with this dependable clamp. Ideal for studio use, yet equally as useful for location-based shoots, it is lightweight and portable, so you'll hardly notice it in you kitbag. Designed in Italy with the highest standards of quality, it's built-to-last and withstand wear and tear throughout its long lifespan.
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Extra leg sets are also available. Casters are available. We also carry staircases. Large staircase fits 3' and 4' leg usage, Small staircase fits 1' and 2' leg usage. DESCRIPTION: Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 4000 lbs. load capacity
DESCRIPTION: Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
This photo variable friction arm is both clever and versatile - thanks to its interchangeable 1/4'' Attachments and a 3/8'' Adapter. It is also strong and easy to use - designed to complement a full range of adapters. Which means that you will be able to mix and match and always get the exact kit and setup you need on the day. Even more, it gives you the peace of mind you need to focus on the job at hand.
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Extra leg sets are also available. Casters are available. We also carry staircases. Large staircase fits 3' and 4' leg usage, Small staircase fits 1' and 2' leg usage. DESCRIPTION: Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 2000 lbs.
8" Swivel Caster. Heavy duty white nylon swivel caster. Shaft needs to be fitted with caster sleeve to fit to standard deck corner post. Useful for turning a Steeldeck® platform into a cart for moving decks or other objects. Whole platforms can be built on casters at any height up to 8' for moving heavy objects (cars, scenery etc.). TECHNICAL SPECIFICATIONS: 2000 lbs.
5 step stair unit. Constructed from steel tubing and extruded aluminum treads. Max. height 40" with 8" rise. Min. height 20" with 4" rise. Unit can be attached to any deck edge that is 4' or more in length. Finish: Aluminum
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 1000 lbs.
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 750 lbs
Each deck comes with one set of legs. The legs come in 1’ through 5’ heights. Standard Steeldeck® platform constructed using steel truss frame with high quality ¾" plywood tops. Tops are insulated from frames to reduce noise and vibration. Standard deck will accept 4 legs of 1½" Schedule 40 steel pipe. Legs are held in place by a hand knob. Decks are connected to each other by bolting through pre-drilled holes along each edge. TECHNICAL SPECIFICATIONS: 1500 lbs.
Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
Standard leg supplied in steel pipe. Any length of leg can be supplied. Standard stock heights shown below. All legs supplied with black plastic inserts to protect studio floors. All legs supplied galvanized Load Capacity 6000 lbs.
12" caster and bracket allows a rolling Steeldeck® platform to be built at a finished height of 12". Four casters are used per platform, and platforms can be joined together to make larger rolling stages. Made from steel, with a non-marring rubber wheel. Each caster is fitted with a brake which prevents the wheel from both rolling and castering. Wheels caster within the plan of each deck, so platforms can be brought together. Ideal for rolling drum risers. TECHNICAL SPECIFICATIONS: 400 lbs
3 step stair unit. Constructed from steel tubing and extruded aluminum treads. Max. height 24" with 8" rise. Min. height 12" with 4" rise. Unit can be attached to any deck edge that is 4' or more in width. Finish: Aluminum